DEAD FRONT FOR WALL MOUNT ENCLOSURES

Dead front panels are designed as a fixed depth panel to be mounted directly behind the existing hinged door. This allows space to mount gages, meters and push buttons directly behind the front door making them easily visible when mounting them through the main door is not an option. Dead front panels also provide a barrier against incidental contact with live components during routine monitoring or maintenance of equipment. 

[More Info]

TYPE 4X STAINLESS STEEL ENVIROLINE® SERIES WALL MOUNT WITH 3 POINT HARDWARE

This Stainless Steel Enviroline wall mount enclosure has been designed for indoor or out door type 3R, 12, 4 & 4X applications.  This enclosure line was also designed with 3 point door hardware for easier access and can be securely locked to provide protection to personnel against access to hazardous parts.  In addition, it protects the equipment inside the enclosure against introduction of solid foreign objects, falling dirt, rain and spraying water in corrosive environments.

[More Info]

American Recovery and Reinvestment Act of 2009

Saginaw Control & Engineering would like to make the following statement:

The American Recovery and Reinvestment Act of 2009 (ARRA) contains a Buy American provision in Section 1605.  Based on currently available guidance on this provision, Saginaw Control & Engineering will comply with the Buy American provisions of the ARRA as they relate to Federal aid for EPA funded projects.

The basis for the foregoing statement is that the Electrical Enclosures provided by Saginaw Control & Engineering are a domestic manufactured good as defined at 2 CFR 176.140(a) or 2 CFR 176.160(a), as applicable, assembled, tested and integrated in the United States prior to shipment to the project site.

[More Info]

Desk Console Series

This product is intended for indoor use.  It provides protection to personnel against access to hazardous parts.  In addition, it protects the equipment inside the enclosure against introduction of solid foreign objects, falling dirt and water.  It is designed for use in a standing or sitting position, supports both single and dual access, and boasts a top that opens for easier accessibility.

[More Info]

Historic Price Decrease

11^th Edition Catalog

Saginaw Control & Engineering is proud to announce the release of our new 11^th Edition Catalog. Additions to this catalog include:

• Type 4X Enviroline Two Door Stainless Steel Sloping Top Enclosure
  Page 205
• Type 4X Enviroline Wall Mount Stainless Steel Sloping Top Enclosure
  Page 203
• Type 4X Enviroline Two-Door Sloping Top Disconnect Enclosures
  Page 231
• Type 4X Enviroline Wall Mount Sloping Top Disconnect Enclosures
  Page 233
• Fan Heaters with Thermostat
  Page 266
• Internal Disconnect Enclosure / Arc Flash Enclosure
  Page 256
• Type 4X Enviroline Two Door Stainless Steel with 3pt
  Page 199
• Type 4X Enviroline Two Door 316 Stainless Steel with 3pt
  Page 199
• Type 4 Enviroline Two Door Steel with 3pt
  Page 165
• Type 4 Enviroline Wall Mount Two Door with 3pt
  Page 163
• Type 4X Enviroline Wall Mount Two Door Stainless Steel with 3pt
  Page 163
• Type 12 Program Ports
  Page 284

Order yours today!

ENVIROLINE ® Sloping Top Enclosures

Designed with a 15 degree sloping top to reduce or eliminate debris or sediments from accumulating or pooling on the top of the enclosure in a wet or wash down application. Available in disconnect and non-disconnect, floor mount and wall mounted versions. 43 standard sizes and configurations to choose from. Stainless Steel Type 12, 4, & 4X.

[More Info]

ENVIROLINE ® Two Door Enclosures with Three Point Door Hardware

Designed for indoor and outdoor applications. Available in floor mount and wall mounted versions. More than 50 standard sizes and configurations to choose from. Stainless Steel Type 12, 4 & 4X and Carbon steel powder coated ANSI 61 gray Type 12 & 4.

[More Info]

Fan Heaters

Designed to protect electrical controls, instruments and sensitive components from low temperatures and the effects of condensation and corrosion by maintaining a stable temperature within the electrical enclosure. These heaters are not intended for use in hazardous, wet, dusty or dirty locations. For installation information, consult our Installation Manual.

[More Info]

Type 3R Vented Enclosure

Saginaw Control & Engineering's Vented Type 3R Enclosures are designed to house electrical controls, drives, instruments and components used in an outdoor environment to provide a degree of protection for the equipment inside the enclosure against ingress of solid foreign objects (falling dirt); and provide a degree of protection with respect to the harmful effects on the equipment due to the ingress of water (rain, sleet, snow). This design incorporates a rain cap that acts as a solar shield to minimize solar heat gain, rain hood with filters for air intake and cooling fans exhaust out the top to control internal heat load, with six standard sizes available.

[More Info]

Lenoir City, Tennessee Distribution Center

Lenoir City Industrial Park
220 Sam Rayburn Parkway
Lenoir City, Tennessee 37771
Phone: (865)717-4861
(866)710-4717
Fax: (865)717-4924
E-mail: LenoirCity@SaginawControl.com

Internal Disconnect Enclosures

Increase personal protection against Arc Flash and Shock Hazards, with the Internal Disconnect Enclosure. This enclosure can be used within an environmentally rated enclosure to isolate the main power supply, increasing personal protection by preventing incidental contact or exposure to the high voltage arc flash and shock hazard, and potentially reducing the PPE level for the lower risk components when the Internal Disconnect Enclosure cover is closed.

The Internal Disconnect Enclosure can be easily incorporated into a new system or added to a pre-existing system with variable depth or cable operated disconnects. The Internal Disconnect Enclosure aids in achieving compliance with NFPA 70E by concealing the main power supply.

[More Info]

Program Ports

Saginaw Control and Engineering has added a new line of program ports. This new product line is a great way to increase your compliance with NFPA 70E and reduce the risk of personal exposure of arc flash by reducing the need to access the enclosure, by bringing GFCI utility outlets and data interface ports outside the enclosures.

Features:

• UL Recognized Type 1, 12 & 4
• CSA Approved Type 1, 12 & 4
• CE & NFPA 70E Compliant
• 10 Standard Configurations
• Available with Ethernet, Control Net, Serial or Device Net data interface ports
• GFCI Ground fault circuit interrupters with exclusive three outlet design, GFCI Duplex outside the enclosure with GFCI Simplex inside.
• Transparent sealed cover.
• Quick release padlocking latch.

Industrial Modular System (IMS) Enclosures

Designed for Type 12 industrial applications, a heavy duty one piece construction with integrated mounting channels in the top and bottom of the enclosure makes this product more flexible and easier to work with and with 40 different enclosure sizes and configurations to choose from, the IMS is a perfect fit to any industrial application.

[More Info]

Slope Top Workstations

Design for indoor or out door type 12, 4 & 4X applications this design incorporates a 20 degree slope top to prevent unwanted debris or liquids from pooling or collecting on the top of the enclosure in a wet or wash down environment. A 12.5 degree sloped keyboard desk aids in a comfortable ergonomic working surface.

[More Info]